Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
Just how do you really feel when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a tub isn't specifically rocket science, yet it does need solid plumbing, carpentry, and also often, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably hard project. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly require a helper to vacate the old bathtub and embeded in the new one. Ensure you have actually certified on your own for the task as well as are comfortable trying it. Rather than employing a professional to take control of a halfway-completed task, it is much better to think about using one before you begin. Possibilities are you may require an expert plumber to make tube links.
This post will certainly help you install a brand-new bathtub in your restroom if you have actually already gotten a brand-new tub as well as don't require to change the arrangement of your previous water system pipelines.
Your devices as well as material checklist should comprise the following:
Preparing for the Setup
First of all, the sustaining structure provided with the bathroom must be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets device to stop strain on the tub.
Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you should do is separate the water system. After doing so, activate the taps to drain any water remaining in the system. The process of eliminating the existing faucets can be rather problematic due to the restricted accessibility that is frequently the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will originate from the pipes. When the supply pipes have actually been removed, make use of the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Before going on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are practical in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The next objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the tub up until the spirit level reviews degree.
To install taps, fit the bottom of the furthest flexible tap adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and also examine all joints and also new pipework for leakages and also tighten them if essential. Load the tub and additionally check the overflow outlet and also the regular electrical outlet for leaks.
Ultimately, deal with the bath paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the bathtub should wait up until the bathtub has been used at the very least once as this will certainly resolve it right into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will require minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washers are in place in between the tap as well as the sink. Secure the faucet in place with the manufacturer offered backnut. As soon as the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The previous kind needs to be attached to the tap finishes first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to break an inflexible seal, causing the water to penetrate the wall surface between the bathroom as well as the tiling, bring about difficulties with moisture and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and installations. They are sold in tubes and also cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to securing, to permit the movement experienced when the tub remains in use. The sealer can fracture rather early if you do not think about this activity prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise quickly offered on the market. It is recommended to fit the floor tiles utilizing waterproof or water-proof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I am just very involved in How to Install a Bathtub and I hope you enjoyed the blog post. Those who liked our blog entry if you please be sure to share it. We value reading our article about A Step-by-Step Guide to Installing a Bathtub.
For instant fixes, dial! Report this page